How to use ironing centers?

Ironing centers are very common electrical appliances in daily life, almost everyone will use them. So it is necessary to know the usage and precautions of ironing centers. This article introduces the operation method of ironing centers in detail.

Here is the content list:

• How to use ironing centers?

• The notes for using ironing centers

• The cleaning methods of ironing centers

How to use ironing centers?

Before power on, check whether the protective layer of the outer layer of the wire is complete and whether it is damaged, so as to prevent the occurrence of electric leakage.

If it's an old ironing center, there is no water port. Therefore, when ironing clothes, you need to dip some water on the cloth you touch or spread a wet cloth to prevent the cloth from being damaged.

Steam ironing centers need water, and it is better to use boiled water or purified water without impurities. If it is ordinary tap water, the impurities in it may block the air outlet and affect the effect. In the process of adding water, pay attention to the amount of water, not too little, easy to evaporate in a short time. When pouring water into the water injection nozzle, be careful not to sprinkle the water on other parts of the ironing centers to avoid electric shock.

According to the material you want to iron, select the corresponding temperature range, and then start heating. Don't ignore this step, otherwise, the clothes may be wrinkled and damaged.

During the heating process of ironing centers and during the intermission of ironing, the iron should be placed vertically instead of being put aside, as it is easy to burn the articles in direct contact with the iron.

After the steam ironing centers are used up, if there is still residual water, either pour it out or continue to power on until the water is dried. If the water is not evaporated, the water may leak out and adhere to the bottom plate, leaving water stains, which is not conducive to the maintenance of the machine.

The notes for using ironing centers

Ironing centers are a kind of high-power electrical appliance. When using ironing centers, you should pay attention to the following:

1. The power supply of ironing centers must be a three-phase plug, and there must be a grounding or neutral protection device.

2. Since ironing centers are at least 300 watts in power, it is necessary to use thicker wires to connect the iron to ensure sufficient capacity.

3. The household electric meter should have enough capacity. Generally, the 300 Watt electric iron needs 2.5 a meter, the 500 Watt electric iron needs 3A meter, the 750-watt electric iron needs 5 a meter, and the 1000 watt electric iron needs 10 a meter.

4. When using the interval, the electric iron should be placed vertically, or placed on the iron block, ceramics, and other insulation materials, so as to avoid igniting the articles.

5. Protect the connecting line of ironing centers to prevent breaking and leakage.

6. When using, do not let children get close to it to prevent children from touching and scalding.

7. After using it, you should wait for ironing centers to cool naturally before you can collect it.

8. There is a drip switch in front of the handle of steam ironing centers. When the temperature is high enough, the water will evaporate into steam and eject from the bottom hole. If the temperature of the iron board is too low, the water will not evaporate and form water leakage. Press it again to turn off the water.

The cleaning methods of ironing centers

1. Clean the ironing centers until they are completely cooled. It can be scrubbed with a soft wet cloth. If the coking clothes stick to the bottom plate, they can not be scraped off by force to avoid damaging the coating. It can be wiped off with cuttlefish bone.

2. Ironing centers can only be put away after they are fully cooled. During storage, in order to avoid coating damage, it is better to place it vertically.

3. When not in use, the temperature control steam ironing centers should turn the temperature knob to the lowest and the steam knob to the dry ironing position.

4. The power cord should not be rolled too tightly to avoid damaging the core.

5. After using steam ironing centers for a period of time, if white powder appears in the steam spray hole, you can inject water with white vinegar into the iron, heat it for 10 minutes, turn off the power, shake the iron for cleaning, then pour it out, and rinse it with clean water several times.

Easton Hotel Supplies Co., Ltd. conducts a lot of tests on ironing centers before leaving the factory to ensure quality. If you are in the ironing centers business, you can consider using our cost-effective products.